Click Image for Gallery

Weldclass WC-03766 - 1.2mm 4.5kg Hardfacing CX-1800 Gasless MIG Wire

Features:

Long-Life hardfacing 'MIG' wire for ground-engaging equipment.
Very high resistance to abrasion with up to 3-4 times better wear life vs basic hardfacing wires
Special carbide additives not found in other wires.
Recommended for metal-to-earth applications where wear is mostly caused by abrasion, with low-to-medium impact; points, tynes, buckets, teeth, screws, augers, grousers, etc.
Gasless wire for easy application.
Available in 1.2mm in 15kg or 4.5kg spools.
Requires minimum 140 amps
Suitable for use with 200A-250A MIG welders.

Application Information:

Typical hardness 59-61 HRc (max hardness achieved with 2 layers)
Ideal for ground-engaging agricultural and earthmoving tools subject to high abrasion and low-to-moderate impact

Surface Preparation:

VERY IMPORTANT: Surface to be hard faced must be clean and free of rust, scale, grease, moisture & other contamination.
If existing/old hardfacing deposits are loose they should be removed. (Hammer test can confirm bond strength of existing deposits, a "ping" indicates good bond and a "clack" indicates a separation layer which must be ground off).
Buffer Layer / Pre-Heat: CX-1800 will typically weld easily to most common surfaces WITHOUT the need for buffer layer or pre-heat, such as mild & high carbon steel, cast steel, etc
If applying to hard-to-weld steels, or hard-to-weld existing deposits, use buffer layer of 309 or 312 wire or electrodes. Whilst not essential, pre-heat of 150-350c may be beneficial.
If applying to high-manganese (non-magnetic) steel, buffer of specialist high-Mn/Cr wire should be used.

Operating Data:

Polarity: DC+ (torch/wire positive)
Typical parameters: 140-200A @ 18-22V
VERY IMPORTANT: Amperage & voltage should be as low as possible within the recommended range. Applying excessive heat/voltage will reduce the performance and wear life of the weld deposit, due to excessive alloying with base material
Layers: Suitable for multi-layering (up to 3 layers)
Positions: Flat / downhand only (not suitable for vertical or overhead)

Finish:

Surface normally relief-checks (forms fine micro cracks) after welding
Weld deposit is NOT machineable
Weld deposit IS grind-able

How does platinum CX-1800 compare to hyundai CRC?

Composition: Both wires carry a high % of chromium (Cr) for abrasion resistance - however CX-1800 includes additional proprietary carbide additives not found in other wires, for very high abrasion resistance and long-life
Hardness: CrC = 54-57 HRc, CX-1800 = 59-61 HRc
Wear-life multiple vs mild-steel*: CrC = 430%, CX-1800 = 600%
Both wires are gasless, and are recommended for metal-to-earth applications where wear is mostly caused by abrasion, with low-to-medium impact
Summary: CX-1800 can be used in all applications where CrC is/has been used, but will offer longer service lift due to significantly higher abrasion resistance

*Approx, as per ASTM G65 standard

Specifications:

Wire: 1.2 mm
Spool Diameter: 200 mm
Weight: 4.5 kg

If you have any queries about Freight, please Call: 07 3363 0555 or Email: web@cltoolcentre.com.au

**We are able to dispatch goods Australia wide**

** Cut Off Time For Overnight Orders is 11:30 am Subject To Stock Availability **

** International orders are accepted at our discretion, Please contact our sales team for terms conditions & charges related to overseas orders**

Discounted Flat $9.50 Shipping For Orders Over $99 (Conditions applied)

C&L Tool Centre now offers a discounted flat shipping fee of $9.50 for all orders over $99 on a single transaction depending on shipping weight and Destination Zone. Please see the table below for details. Orders under $99 on a single transaction will have delivery fees calculated based on your delivery postcode, as well as the weight and size of the items in your cart.

The total shipping weight* of the order must be below 20KG and the dimensions of the package have a maximum length of 1m and package volume of 0.25m³. (*Shipping weight is the higher of the actual weight or the cubic weight.)

Items that exceed the above weights and dimensions or not meet requirements in Table 1 may incur an additional freight charge and we will contact you prior to the dispatch to advise and confirm any freight charges.

C&L Tool Centre reserves the right to remove this offer without notice.

Table1:

Orders Over $99: Discounted Flat Shipping Fee - Terms and Conditions
Destination Zone		Cart Total Requirement For Different Shipping Weight and Zone				Postcode
Destination Zone						Postcode
Zone	Name	0-3KG	3.01-6KG	6.01-10KG	10.01-20KG
Q0	Brisbane Metro	>=$99				4000-4018, 4029-4068, 4072-4123, 4127-4129, 4131-4132, 4151-4164, 4169-4182, 4205-4206, 9000-9725
Q1	Brisbane					4019-4028, 4069-4071, 4124-4126, 4130, 4133-4150, 4165-4168, 4183-4204, 4207-4209, 4270-4299, 4500-4549
GC	Gold Coast					4210-4224, 4226-4269, 9726-9919
IP	Ipswich					4300-4308
SC	Sunshine Coast					4550-4579
N0	Sydney Metro	>=$99		>=$199		1000-1935, 2000-2079, 2085-2107, 2109-2156, 2158, 2160-2172, 2174-2229, 2232-2249, 2557-2559, 2564-2567, 2740-2744, 2747- 2751, 2759-2764, 2766-2774, 2776-2777, 2890-2897
N1	Sydney					2080-2084, 2108, 2157, 2159, 2173, 2230-2231, 2508-2514, 2555-2556, 2560-2563, 2568-2574, 2745-2746, 2752-2758, 2765, 2775, 2778-2786
N4	Tweed Heads					2485-2486
V0	Melbourne Metro					3000-3062, 3064-3098, 3101-3138, 3140-3210, 3800-3801, 8000-8999, 9999
V1	Melbourne					3063, 3099-3100, 3139, 3335-3341, 3427-3443, 3750-3799, 3802-3811, 3910-3920, 3926-3944, 3975-3978, 3980-3983
Q5	Coolangatta					4225
Q2	QLD Country Near					4309-4453, 4580-4693
Q3	QLD Country Mid	>=$99	>=$199	>=$299	>=$399	4454-4499, 4694-4802, 4804-4805, 9920-9960
GF	Gosford					2250-2263
WG	Wollongong					2500-2507, 2515-2532
NC	Newcastle					2282-2310
CB	Canberra					200-299, 2600-2620, 2900-2920
S0	Adelaide Metro					5000-5113, 5115-5117, 5125-5130, 5158-5169, 5800-5999
S1	Adelaide					5114, 5118-5124, 5131-5157, 5170-5200
N3	Albury					1936-1999, 2640-2641, 2708-2709
N2	NSW Country					2264-2281, 2311-2484, 2487-2499, 2533-2554, 2575-2599, 2621-2639, 2642-2647, 2649-2707, 2710-2714, 2716, 2720-2730, 2787-2879
V3	Wodonga					3689-3690
Q4	QLD Country North					4803, 4806-4999, 9961-9998
GL	Geelong					3211-3220
W0	Perth Metro					6000-6030, 6036, 6050-6066, 6069, 6076, 6090-6110, 6112-6120, 6147-6160, 6162-6175, 6180, 6182-6206, 6210, 6800-6990, 6992-6996 (UP TO 3KG)
W1	Perth					6031-6035, 6037-6049, 6067-6068, 6070-6075, 6077-6089, 6111, 6121-6146, 6161, 6176-6179, 6181, 6207-6209, 6211-6214, 6991, 6997-6999 (UP TO 3KG)
T0	Tasmania Select	>=$199	>=$299	>=$399	>=$699	7000-7019, 7050-7053, 7055-7108, 7172, 7248-7254, 7258-7329, 7800-7999 (UP TO 3KG)
T1	Tasmania					7020-7049, 7054, 7109-7150, 7155-7171, 7173-7247, 7255-7257, 7330-7799 (UP TO 3KG)
BR	Ballarat					3350, 3353-3356
V2	VIC Country					2648, 2715, 2717-2719, 2731-2739, 3221-3334, 3342-3349, 3351-3352, 3357-3426, 3444-3688, 3691-3749, 3812-3909, 3921-3925, 3945-3974, 3979, 3984-3999
AAT	Aust Antarctic Territory*					7151-7154 (UP TO 3KG)
S2	SA Country					2880-2889, 5201-5749
NT1	NT Near					0800-0802, 0804-0821, 0828-0851, 0853-0853, 0860-0861, 0870-0871, 0873-0879, 0906-0999 (UP TO 3KG)
NT2	NT Remote					0803-0803, 0822-0827, 0852-0852, 0854-0859, 0862-0869, 0872-0872, 0880-0905 ((UP TO 3KG))
NF	Norfolk Is*					2898-2899 (UP TO 3KG)
W4	Christmas & Cocos Is*					6798-6799 (UP TO 3KG)
W2	WA Country South					6215-6700 (UP TO 3KG)
W3	WA Country North					6701-6797 (UP TO 3KG)

Weldclass WC-03766 - 1.2mm 4.5kg Hardfacing CX-1800 Gasless MIG Wire

Weldclass
Product Code: WC-03766
Warranty: Manufacturer Warranty*